B-292 Mirror with Shelf

Bobrick Angle-Frame Mirror with Shelf Stainless Steel

Ordering Mirrors

Size - smaller mirrors can ship via UPS, but they won't take larger mirrors.  Those must ship via motor freight adding a large amount to the overall cost.  In general, UPS will take up to 18 x 30 size, but it varies by model number.

Breakage - it is common for mirrors to break during shipping regardless of how they are shipped.

It is critical that you inspect for breakage when mirrors are delivered.

If you sign for a mirror only to discover later it is broken, then you own it.  We cannot file a claim against the shipping company if you signed for it.

It is easy to check for a damaged mirror.  Just hold up the box and shake it a little.  If you hear broken glass, then note the damage on the shipping ticket.  The driver will take it back.  This is the only way we can make the shipping company pay for the damage.

Designer's Notes:
1. Special-order sizes available on request.
2. Maximum size one-piece angle-frame mirror, 144'' x 72'' (366 x 183cm); minimum size, 12" x 12" (30 x 30cm). Maximum frame size available, 186" x 72"
(472 x 183cm) with two pieces of glass in one-piece frame. Stainless steel I-section with polished finish covers seam where two pieces of glass butt together.
3. Shelves longer than 120" (305cm) will be furnished as two pieces butted together.
4. All Bobrick framed mirror/shelf models are manufactured to overall width and height dimensions. EXAMPLE: A 24'' x 36'' (61 x 91cm) mirror will be furnished
24'' x 36'' (61 x 91cm) outside-of-frame to outside-of-frame including shelf.
5. To specify special sizes use Series Number followed by width then height in inches. EXAMPLE: B-292 2024.
6. Bobrick framed mirror/shelf models are manufactured to a tolerance ± 1/8'' (3.2mm).
7. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4'' (85mm) minimum clearance above center line of mounting screw holes.
8. Provide 1'' (25mm) minimum clearance at bottom of mirror for engaging locking screws and 1'' (25mm) clearance on each side.

MATERIALS: Frame — 18-8 S, type 304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with vertical-grain satin finish. Onepiece, roll-formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame tightly against mirror. Corners of mirror frame are heliarc welded, ground, and polished smooth. Galvanized steel back is fastened to frame with concealed screws and equipped with integral horizontal hanging brackets near the top for hanging the mirror and near the bottom to prevent the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. In Screw Locking Design, concealed Philips-head locking screws securely fasten mirror to wall hanger. Shelf — 18-8 S, type 304, 22-gauge (0.8mm) stainless steel with satin finish, 3/4" (19mm) return edges on front and sides. Front return edge hemmed for additional strength and safety. Front corners of shelf are welded, ground, and polished smooth. Shelves over 36" (915mm) long are constructed of 18-gauge (1.2mm) stainless steel. Shelf is welded to mirror frame and reinforced by concealed 16-gauge (1.6mm) stainless steel brackets. No exposed rivet-heads, screws, or fasteners of any type on frame or shelf. Designer's Note: Type 304 stainless steel provides superior corrosion resistance, compared to 400 Series stainless steel, against environmental moisture, hose-down maintenance and strong cleaning solution. Mirror — No. 1 quality, 1/4" (6mm) select float glass: selected for silvering, electrolytically copper-plated by the galvanic process, and guaranteed for 15 years against silver spoilage. All edges protected by plastic filler strips; back is protected by full-size, shock-absorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Concealed Wall Hanger — 20-gauge (0.9mm) galvanized steel. Incorporates lower support member, forming rigid rectangle, which engages lower backplate louvers to keep bottom of mirror against wall.

INSTALLATION: Mount wall hanger on wall with screws (furnished by manufacturer) at points indicated by an S. For plaster or dr y wall construction, provide backing to comply with local building codes, then secure wall hanger with screws furnished. When providing a concealed backing, allow backing to cover minimum range of mounting hole locations shown on drawing. For other wall surfaces, provide fiber plugs or expansion shields for use with screws furnished, or provide 1/8" (3mm) toggle bolts or expansion bolts. Hang mirror on wall hanger with all four backplate louvers engaged behind horizontal wall hanger members. To do this, mirror must be centered in front of the wall hanger horizontally, pressed flat against the wall approximately 1" (25mm) above final position and then lowered into final position.SPECIFICATION: Mirror shall have a one-piece, type 304 stainless steel angle frame, 3/4" x 3/4" (19 x 19mm) with continuous integral stiffener on all sides and beveled front to hold frame tightly against mirror; corners shall be heliarc welded, ground, and polished smooth; all exposed surfaces shall have satin finish with vertical grain. Shelf shall be type 304 stainless steel with satin finish; shelves up to 36" (915mm) long shall be 22 gauge (0.8mm) and larger shelves shall be 18 gauge (1.2mm). Shelf shall have 3/4" (19mm) return edges on front and sides with front return edge hemmed and corners welded, ground, and polished smooth. Shelf shall be welded to mirror frame and reinforced by concealed stainless steel brackets. No rivet-heads, screws, or fasteners of any type shall be exposed on frame or shelf. Select float glass mirror shall be guaranteed for 15 years against silver spoilage. All edges shall be protected by plastic filler strips and the back shall be protected by full-size, shockabsorbing, water-resistant, nonabrasive, 3/16" (5mm) thick polyethylene padding. Galvanized steel back shall have integral horizontal hanging brackets located at top and bottom for mounting on concealed rectangular wall hanger and to prevent the bottom of the mirror from pulling away from the wall. Locking devices secure mirror to concealed wall hanger. Mirror shall be removable from wall hanger for reglazing mirror. Snap Locking Design — Locking devices automatically secure mirror to concealed wall hanger when it is lowered into final position. Locking devices may be unlocked by inserting two flat blade screwdrivers behind each side of mirror near the bottom or under the bottom of the mirror and pulling mirror bottom forward and then up.